Linux配置ip地址的兩種方法，實驗環境為centos7.6

方法1：nmcli工具配置 （centos7以下版本不支持該方法）

第一步，通過nmcli connection查看網卡名稱

[root@localhost ~]# nmcli connection
NAME UUID TYPE DEVICE
eth0 09be0948-faf1-43b6-a5a4-c19efab0bb48 ethernet eth0

第二步，配置ip，網關，dns，并設置網卡開機自動啟動，最后開啟網卡

[root@localhost ~]# nmcli connection modify eth0 ipv4.addresses “192.168.1.201/24”

說明：配置地址和掩碼

想要獲取更多技術干貨和資料，可以加群752160765一起學習哦！

[root@localhost ~]# nmcli connection modify eth0 ipv4.gateway “192.168.1.1”

說明：配置網關

[root@localhost ~]# nmcli connection modify eth0 ipv4.dns “180.76.76.76”

說明：配置dns

[root@localhost ~]# nmcli connection modify eth0 ipv4.method manual

說明：地址獲取的方法為手動配置而不是dhcp

[root@localhost ~]# nmcli connection modify eth0 autoconnect yes
說明：開機自動打開網卡

[root@localhost ~]# nmcli connection up eth0

說明：立即打開網卡

Connection successfully activated (D-Bus active path:
/org/freedesktop/NetworkManager/ActiveConnection/4)
第三步，查看結果（這里使用ip addr命令查看，較新版本Linux系統支持該命令）

[root@localhost ~]# ip addr

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever

2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:0c:29:84:23:62 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.201/24 brd 192.168.1.255 scope global noprefixroute eth0
valid_lft forever preferred_lft forever
inet6
fe80::b7ad:e2ed:832e:99a9/64 scope link noprefixroute
valid_lft forever preferred_lft forever
測試通信

[root@localhost ~]# ping www.baidu.com
PING www.a.shifen.com (61.135.169.121) 56(84) bytes of data.
64 bytes from 61.135.169.121 (61.135.169.121): icmp_seq=1 ttl=53 time=34.7 ms
64 bytes from 61.135.169.121 (61.135.169.121): icmp_seq=2 ttl=53 time=27.9 ms
64 bytes from 61.135.169.121 (61.135.169.121): icmp_seq=3 ttl=53 time=24.1 ms
64 bytes from 61.135.169.121 (61.135.169.121): icmp_seq=4 ttl=53 time=25.2 ms
64 bytes from 61.135.169.121 (61.135.169.121): icmp_seq=5 ttl=53 time=24.2 ms
^C
— www.a.shifen.com ping statistics —
5 packets transmitted, 5 received, 0% packet loss, time 4005ms
rtt min/avg/max/mdev = 24.177/27.277/34.718/3.970 ms

方法2：通過vi編輯網卡配置文件（最新版rhel8或centos8不推薦該方法，老版本rhel6及以下推薦該方法）

第一步，通過vi或vim打開配置文件

[root@localhost ~]# vim /etc/sysconfig/network-scripts/ifcfg-eth0

第二步，編輯相關的參數

TYPE=Ethernet
PROXY_METHOD=none
BROWSER_ONLY=no
BOOTPROTO=none
DEFROUTE=yes
IPV4_FAILURE_FATAL=no
IPV6INIT=yes
IPV6_AUTOCONF=yes
IPV6_DEFROUTE=yes
IPV6_FAILURE_FATAL=no
IPV6_ADDR_GEN_MODE=stable-privacy
NAME=eth0
UUID=
09be0948-faf1-43b6-a5a4-c19efab0bb48
DEVICE=eth0
ONBOOT=yes
IPADDR=192.168.1.202
PREFIX=24
GATEWAY=192.168.1.1
DNS1=180.76.76.76
PEERDNS=no
vi的編輯方法是，輸入字母i，進行編輯，編輯完成后，按esc，再按:wq 保存退出。如果不保存，則是:q!退出

第三步，重啟網絡服務

[root@localhost ~]# service network restart
Restarting network (via systemctl): [ OK ]

第四步，查看結果并測試通信（這里用ifconfig命令來查看，各種版本Linux均支持該命令）

[root@localhost ~]# ifconfig eth0
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.202 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::b7ad:e2ed:832e:99a9 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:84:23:62 txqueuelen 1000 (Ethernet)
RX packets 1117 bytes 127303 (124.3 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 564 bytes 69559 (67.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

[root@localhost ~]# ping www.baidu.com
PING www.a.shifen.com (61.135.169.125) 56(84) bytes of data.
64 bytes from 61.135.169.125 (61.135.169.125): icmp_seq=1 ttl=53 time=28.2 ms
64 bytes from 61.135.169.125 (61.135.169.125): icmp_seq=2 ttl=53 time=30.9 ms
^C
— www.a.shifen.com ping statistics —
3 packets transmitted, 2 received, 33% packet loss, time 2003ms
rtt min/avg/max/mdev = 28.228/29.590/30.953/1.373 ms
[root@localhost ~]#

配置地址的兩種方法就介紹到這里。

但是查看地址時，我們并沒有看到網關和dns，那么網關和dns怎么看呢，用以下兩條命令即可

[root@localhost ~]# route -n 通過查看路由表來知道網關

Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 192.168.1.1 0.0.0.0 UG 100 0 0 eth0
[root@localhost ~]# cat /etc/resolv.conf 通過查看rsolv.conf文件來查看dns
# Generated by NetworkManager
nameserver 180.76.76.76